產品品牌：九康 產品型號：JK-DF/250-20 詳細說明

介質材料:有機薄膜	應用范圍:低壓
外形:方塊狀	功率特性:小功率
頻率特性:低頻	調節方式:微調
引線類型:無引線	允許偏差: 5（%）
耐壓值:350（V）	標稱容量:1020（uF）
額定電壓:250（V）

概述General Description

JK系列智能集成電力電容器是0.4kV低壓電網高效節能、降低線損、提高功率因數和電能質量的新一代無功補償設備。它由智能測控單元、過零投切開關電路、保護單元、兩臺(△型)或一臺(Y型)低壓電力電容器構成。替代常規由智能控制器、熔絲、復合開關或機械式接觸器、熱繼電器、低壓電力電容器、指示燈等散件在柜內和柜面由導線連接而組成的自動無功補償裝置。改變了傳統無功補償裝置體積龐大和笨重的結構模式，從而使新一代低壓無功補償設備具有補償效果更好，體積更小，功耗更低，價格更廉，節約成本更多，使用更加靈活，維護更加方便，使用壽命更長，可靠性更高的特點，適應了現代智能電網對無功補償?shù)母咭蟆?/p>

JK series intelligent integrated power capacitor bank as a new generation of reactive power compensating device, is used in 0.4KV low voltage network, to realize energy saving, reduce the line loss, improve power factor and electric quality, it consists of intelligent monitoring device, over-zero switching circuit, protective unit, two pieces of (△ connection) or one piece of (Y connection) low voltage power capacitor(s), substitute for the traditional compensating system constructed in cabinet by use of intelligent controller, fuses, combination switch or mechanical contactor, thermal relay, low voltage power capacitor, indicators and etc accessories, which sweep away the defect of large space and heavy weight in traditional devices, realize better compensating effect, smaller size, lower onsumption loss, lower cost, the maintenance is more convenient, longer working life, and higher reliability, it can completely meet with the requirement of latest intelligent reactive power compensating for modern power network.

技術指標

1、使用條件：海拔2000米以下，環境溫度-25℃~ 50℃；相對濕度20℃, 90%。
2、額定電壓：250VAC、50Hz。
3、額定容量：共補5-40kvar，分補5-20kvar。
4、電容允差：-5~ 10%。
5、最高允許過壓：110%額定電壓。

主要特點

1、體積小、安裝簡便，可隨機就地智能補償，只需補接信號輸入即可進行自動投切。
2、可一機自動智能，亦可多機聯網智能，實現多機自動聯網投運，無需再增控制器 控制。
3、集成電容可自動顯示功率因數、電網電壓、電網二次電流、產品溫度及產品故障顯示。
4、可根據實際情況設定投入功率因數，切除電壓設定等。

產品應用電氣連接及接線示意

1、產品的配線要求
產品與電源端的連接導線規格：一般情況，單臺總?cè)萘繛?0kvar以
上的共補和總?cè)萘繛?0kvar分補電容器，應采用標準16mm2截面積的多
芯銅導線，其余規格的產品采用標準10mm2截面積的多芯銅導線。
產品與產品間的信號線連接導線規格：信號線包括電流取樣線、RS-
485通信線、指示燈線、外控信號輸入線等。信號線上所載電流很小，選
擇強度合適的銅導線即可，一般采用截面積為0.75mm2左右的多芯銅導線。
各臺之間RS-485通信線并接。電流信號線并接后接到JK-CF二次電
流互感器的輸出端。

Technical Index

1. Working conditions: altitude less than 2000m, ambient temperature: -25℃
~ 50℃, relative humidity 90% at 20℃
2. Rated voltage：250VAC、50Hz。
3. Rated capacity: 5-40kvar at compensating together; 5-20kvar at respectively
compensating.
4. Permissible deviation：-5~ 10%。
5.Highest permissible over-voltage: 110% rated voltage

Main Features

1. Small size, easy installation, it can be used for local compensating at any
place, that is able to work after main circuit and signal circuit connected with
this device.
2. One bank can operate independently, several capacitor banks can be interlinked
to operate, no more controller required furthermore.
3. It can display power factor, network voltage, secondary current of network,
capacitor temperature and fault.
4. It can set the capacitor switching-in power factor, voltage cutting-off value
and etc according to the actual conditions.

Wiring Diagram And Illustration Of Product Application

1. Wire requirements
The conductor connected between products and power supply: generally
the capacitor for three phase compensating more than 30KVAr and for respective
compensating more than 20KVar shall adopt the multi-core copper wire with
sectional cross area 16mm2, the others utilize multi-core copper wire with
sectional cross area 16mm2.
The signal wire between products: signal wire including current sampling
wire, RS-485 communication wire, indicator wire, input wire for outside control
signal and etc. the carrying current is small, so it use the copper wire with proper
strength, generally adopt multi-core copper wire with sectional cross area 0.75mm2
The communication wires for RS-485 in each capacitor banks are shunt
connected. The current signal wires are in parallel connected and connected to
secondary output terminal of CT in JK-CF.